Vaporesso VECO DEVIL Tank User Manual

The Vaporesso VECO Devil is the pinnacle of cloud chasing achievement within a Sub-Ohm system, featuring the Vaporesso Eco Universal Coil to deliver the most original flavor of your juice and easy coil replacement system guaranteed. Adopting the cup design of VECO family, it is still top fill and top airflow adjustment with expanded airslots, truly leak free design for a cloud chasing satisfaction.

How To Use
Adjustment of Air Flow: The top airflow system can be adjusted with slight twisting motions of the top lid which will not loosen its attachment to the pyrex glass.

Filling E-liquid: This easy top-fill tank will only ask of you to screw out the lid and fill in the chamber when the base is securely shut.Be sure to safely position the glass part when this process is in place to avoid spillage.

Changing Atomizer: Unscrew the base to simply remove and insert a new atomizer whenever needed. Pull the EUC out from the base and insert a new one. Screw the Base on. Wait after replacing to make sure the coil is well primed.

Warning
1.When using a new atomizer, after filling in e-liquid, let the tank stand for 2 minutes, so the ceramic coil can be saturated with juice before firing
2.Refill the tank before the tank becomes completely empty in order to avoid dry burnt or damage to the atomizer
3.Keep it out of reach of children and pet This device should not be used by persons under the age of 18 or non-smokers.

Ti and Ni Temp Control Mode of IJOY Solo Mini

Are you using IJOY Solo Mini? Do you know how to shift Ni/Ti mode? Take some puffs to find your desired vaping taste before switching to TC mode. Press "T" button IJOY Solo Mini 3 times in quick succession to choose Ni or Ti mode.

1. To shift between Ni/Ti mode please make sure you are in VW mode.
2. Keep pressing the "T" button, the screen will go back to VW mode.
3. Press up and down to choose Ni/Ti mode, then wait 2 seconds and Solo Mini will enter the selected mode automatically. The defaults temperature is 450℉/ 230℃.
4. Press up/down button to set the temperature value, coil temperature can be adjusted from 300-600℉/150-315℃ range. The temperature will be increased in 5℉after each press.
5. The temperature loops between ℉ and ℃.

Vaporesso Swag Starter kit User Manual

How to Use
Switch On/Off: Press the fire button 5 times in quick succession within 2 seconds to turn the device on. In the same way, the device will be powered off after 5 presses.

Vaping: Hold the fire button and inhale through the mouthpiece. Release the fire button and exhale.

Screen Display: After switch on, the OLED displays voltage resistance, battery level, temperature, output wattage etc. Press the fire button at any time, the screen will be lit with main menu.

Automatic atomizer recognition: The mod will read the coil's resistance as soon as the connection is detected. It will also recognize coil type, when a kanthal coil is used, the mod will shift from TC to wattage
mode automatically.

Adjustment buttons lock/unlock: Keep pressing mode button and “+”button simultaneously for two seconds when the device is powered on, then the up and down buttons will be locked and the screen will display “SYSTEM LOCKED”. In the same way, pressing the up and mode buttons can be unlocked and the screen will display “SYSTEM UNLOCKED”.

Switch display mode: Keep pressing up button and down button simultaneously for two seconds ,the screen display will rotate 180 degrees.

Switch vaping modes: Long press the mode button for three seconds to switch among VW(H/N/S) /VT(Ni200, SS, Ti)/ TCR / BYPASS / CCW / CCT modes.

Charging: It is with Quick Charge System and equalizing charge system. Simply plug in the USB cable to charge the battery, OLED display current battery level (0%, 20%, 50%, 80%, and 100%) and the Remaining Charging Time to get the battery fully charge. The Remaining Charging Time will be shown in every 10 minutes. And the display will remain lit while charging.

Firmware update and customizing: Can be updated and customized through a simple software that can be downloaded directly from our website. The software will be made to run on Windows systems and will be available in English. It will also include a “help”sections for urgent questions. The directions on how to use our software will be found on our website and Facebook page.

Adjustment of Air Flow: The top airflow system can be adjusted with slight twisting motions of the top lid which will not loosen its attachment to the pyrex glass.

Filling E-liquid: This easy top-fill tank will only ask of you to screw out the lid and fill in the chamber when the base is securely shut.Be sure to safely position the glass part when this process is
in place to avoid spillage.

Changing Atomizer: Unscrew the base to simply remove and insert a new atomizer whenever needed. Pull the EUC out from the base and insert a new one. Screw the Base on. Wait after replacing to make sure the coil is well primed. Item 10 to 12 only apply to Swag Starter Kit

How to Set the Mode
1) Smart VW mode: As an advanced Variable Wattage mode, there are 3 levels of VW: H stands for High; N stands for Normal; S stands for Soft. The default setting is Normal. VW(H/N/S) will guarantee your mod's ability to skillfully select the adequate average wattage for your atomizer, according to its resistance reading, automatically.

2) In CCW mode: While on VW mode, press the mode button three times consecutively to select CCW. Select and hold down the mode button to confirm and to implement any modifications to
the wattage line using the plus and minus buttons (Ramp up time and consequent performance); move on to the next bar with a quick press of the mode button. When all modifications are final hold pressed the mode button to save and exit.

3) In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2) Mode: When set in TC-Ni/TC-Ti/TC-SS mode, the device can separately support Nickel 200, Titanium, and 316 Stainless Steel coils. The OMNI Board 2.0 allows you to change the start up wattage under temperate control mode. The default wattage is 65W. You could also adjust the value of the coil within the given range. In TCR (Temperature Coefficient of Resistance) mode, the device can support different temperature control coils within different TCR value ranges and you can set the TCR at different values within proper range.

The Setting of TCR Mode (M1,M2):
When set in TC-Ni/TC-Ti/TC-SS mode ,and the device is powered on, you will enter into the TCR (M1,M2) set menu, by clicking mode bottom 3times:
1. Press mode button to choose among M1, M2 ;
2. Press the up or down button to increase or decrease the TCR value according to the material of the coil you used;

Following are different TCR value ranges for different coils for your reference:

Note: 1.The TCR value in the sheet is 10 multiplied of the actual TCR.
2.Our total range of TCR value is 1-1000.

Adjust temperature: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2) mode, temperature can be adjusted from 100-315℃ or 200-600℉ by pressing up button or down button, up button to increase and down button to decrease. Each press of the up or down button will increase or decrease the temperature setting by 5℃ or 10℉. Long press up button or down button can rapidly increase or decrease temperature setting.

Lock/Unlock resistance: In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2) Mode, press the "-"and mode button simultaneously for 2s will lock/unlock the resistance level, “ ” will appear on the display. Attach a new atomizer will not change the locked resistance. Automatic atomizer recognition: To achieve better temperature control effect, the mod will ask the user if the new atomizer is attached. " OLD LOAD: -, NEW LOAD: + " will appear on the display. If a new atomizer is attached, press " + ", the mod will read new resistance; if not, press " - ", the mod will read at locked resistance.

4) In CCT mode: While on any TC mode, press the mode button three times consecutively to select CCT. Select and hold down the mode button to confirm and to implement any modifications to
the temperature line using the plus and minus buttons (Ramp up time and consequent performance); move on to the next bar with a quick press of the mode button. When all modifications are final hold pressed the mode button to save and exit.

5) In Bypass mode: Direct output voltage system is applied in Bypass mode. The higher the batterylevel is, the higher the output voltage is. When set in this mode, the device can support a coil whose resistance is within the range of 0.05-5ohm.

6) Smart ON/OFF:
As an advanced Variable Wattage mode, Smart VW could be switched on and off on the main manual and it does not impact the VW(H/N/S). Enter Smart ON/OFF and press Yes or NO to confirm.

7) Screen Timeout: The timeout setting could be adjusted from 3 seconds up to 60 minutes. Enter the Screen Timeout and adjust the time up or down as you wish.

8) Default: You could reset to default setting by entering Default and pressing YES.

Vandy Vape Govad RDA Preview

Vandy Vape, formed last year has surprises vapers with many its outstanding atomizers including the Vandy Vape Mesh RTA and the Bonza RDA. However, do you still remember its first releases-the Govad RDAs, a collaboration of a team member from the Geekvape and Vandy Vape. It seems that this release has shock the market. Let's have a look at it.

The Govad RDA comes with a Govad deck which adopts almost the same look as the Hadaly deck. The deck also has two airflow inlets that are placed on the either side of the deck. Apart from the side airflow inlets, it also has two bottom airflow inlets which can heat the coil from the underneath. This offers you more choices and you can choose to use which air inlets and have a different vaping experience.

The spring-loaded clamp system which can be found in many some RTAs has the ability to make the whole building of the Govad deck a piece of cake especially when used with a large single coil. This is also one of the outstanding of this Govad RDA.
The Govad RDA is receiving great popular from vapers of a wide range. With the side airflow inlets as well as the bottom airflow inlets, this RDA can deliver you with satisfying vaping experience simply by adjusting the side port or the bottom slots and you can enjoy a denser flavor experience. It seems that the Govad is best compatible with a single coil. However, if you want to use dual coils, you can also make it come true and you can find this by yourself.

Apart from those extraordinary features, the Govad also has a fashionable looking. We are hoping that Vandy Vape will continue to deliver customers with outstanding atomizers with a reasonable price.

IJOY CAPO SRDA KIT - Your First Squonker Kit

If you want to enter into the world of vaping as well as the world of squonking, an easy-to-build and simple-to-use device is what you need now! IJOY, specializing in making squonk mod, launched its another brand-new squonk mod that is both easy to maintain and operate. Today, we are going to have a look at the IJOY CAPO SRDA kit which is also considered the best entry vape kit for squonkers.

Powered by 20700/18650/21700 battery, the mod is capable of outputting 100W, adequate for your daily use. With the fire button and the Squonk bottle at the same side, you can view the e-liquid level when you are vaping. Equipped with a semi-rebuild system, the CAPO SRDA kit is convenient in exchanging the pre- made coil with rebuild decks, finishing the whole process in no time so that you can enjoy vaping as soon as possible.

There is an innovative pre-made coil, you can use the coil to for several times just by changing the cotton. The squonk bottle is large enough for you to hold 9ml e-liquid and it can satisfy your daily use. What’s more, the squonk bottle is very solid so that it is more durable than any other squonk bottles made of ordinary silicon. It is estimated that the squonk bottle of the CAPO SDRA kit is at least ten times durable than common squonk mod. Apart from so many functions, it is very fashionable with many finishes, always a one you like!

Finally, if you are looking for your first squonk mod or if you want to change squonk mods, the IJOY CAPO SRDA Kit will never let you down!

Vandy Vape Bonza RDA Preview -- Not Only A Visual Feast

Vapers are in the pursuit of incredible vaping experience and enchanting design, so the function and appearance of the vape mod and atomizer are becoming increasingly important or most of the vapers no matter what grade they belong to. As a perfectionist, I am always trying to find the best. Also as a vaper, I am greatly satisfied the newest RDA from Vandy vape called Bonza RDA.

Why does it so appealing to me? Now I am going to give you my answers and I am sure you will love it as much as I do after having a clear knowledge of it. It is a partnership between Vandy Vape and The Vaping Bogan, an Australian YouTube reviewer, famous for his YouTube Videos. It is him who integrated his personal vaping style into the design of it. Therefore, it is a considerate vape.

Let's begin with its appearance. The vaping Bogan's skull-and-crossbones logo really impresses me. Holding it in my hand makes me look even cool. What’s more, the choice of color is also a great plus with colorful drip tips for added pizzazz. It is indeed a visual feast. As for its functions, Featuring a 24mm diameter and 25.5mm top cap, it is compatible with most of the vape mods. In addition, the RDA 100% suitable for the Squonk mod with a bottom feeding pin. Besides, the adaption of the uniquely fixed screw-clamp deck configuration is also an innovative move. Other features like the centered dual layout and the 2ml e-juice well all ensures that you can have an easy building and the improved flavor. In conclusion, this Bonza RDA really surprises you!

How to Choose a Proper Atomizer?

We gave some simple introduction to the features of one of the important part of e-cigarette. After posting it on platforms, we received many messages from new hands and those who ready to use e-cigarettes. They showed their admiration to our column. Of course, such concept seems simple for experienced players. But we still want to introduce some basic knowledge of e-cigarettes in the beginning and then go deeply gradually after comprehensive consideration. Our column launched just now. Thank everyone for your support to the column of vaping and hope you can continue to encourage us.

In previous columns, we talked about tobacco oil and main body. We will introduce atomizer in this column. The atomizer of e-cigarettes is a heating element. Powered by batteries, it can heal and atomize inner oil to produce smoke. Therefore, we can achieve the effect of "blowing smoke" when we smoke e-cigarettes. Nowadays, the atomizer can be divided into smoke cartridge (simulating traditional cigarettes), atomizer with oil storage and atomizer of oil drip. Its quality depends on its materials, healing core and making process. Today we mainly talk about the features of "oil storage" and "oil drip" so that you can choose a more suitable device for yourselves.

The atomizer of oil storage can roughly be divided into finished atomizer and DIY atomizer. It has a storage device so users can smoke continuously. It is the common choice for ordinary players.

1. Finished atomizer with oil storage
Finished atomizer means finished atomizing core. Its advantage is convenient using. We can change the atomizing core directly. Its disadvantage is high cost of using the core. One core usually costs about 4 or 5 USD. In general, we need to change our core once a week. If your using frequency is high-cost or the soot deposits into oil are more serious, the using time will be much reduced. Finished atomizer is suitable for new hands and those who have no time or are rich enough to spend a large sum of money on it.

2. DIY atomizer with oil storage
DIY, as the name implies, means we do it by ourselves. It is distinguishable from finished atomizer mainly because its atomizing core can be made by yourselves so it has a lower cost and more ways of playing. DIY atomizer can be separated into the inner storage and outer storage. The former one belongs to atomizing storage, where atomizing core works. The outer storage is for storing oil. In general, a full oil can ensure that you don't need to add oil in a day. There is an oil drain between inner storage and outer storage, which guides oil to the atomizing core by guiding-oil cotton. We will introduce how to make atomizing cores briefly in the latter columns. DIY atomizer can be divided into "flavor reference" and "smoke reference". DIY atomizer is suitable for experienced players.

Atomizer of oil drip output in a way of low resistance and high power. The low resistance can produce much heat energy in a short time to atomize lots of oil and produce big smoke. We can drop tobacco oil into the cotton on the healing core, which is the most efficient and quick way of guiding oil. So it is the favorable choice of senior players.

3. Atomizer of oil drip
Atomizer of oil drip has no oil storage. It just has an atomizing bin. While using it, we need to drop several drips of oil into the cotton and then we can smoke. After several smokes, we need add oil again. It usually has more than one electrode posts, which can be single and multiple. Without oil storage, there is a bigger space for making atomizing core. So players’ imagination can be fully developed.  Its low resistance and big smoke make it more suitable for smoke-show players and senior players.

Nowadays, there are also some atomizer with oil drip and storage and finished and DIY ones, none of them is the main current in the market. However, such atomizers provide more choices for players.

The above is what I want to share with you. Your messages and criticisms are welcomed. You can share your using experience with others. In next column, we will integrate whether e-cigarettes is harmless or not from the technical angel after synthesizing a few senior players' viewpoints. Let us play e-cigarettes together happily. Please look forward!

Wismec Neutron Quick Guide

How to use?
1. Two kinds of atomizer base are available, one for coils in series and the other for coils in parallel. The users then can fix the pre-made or self-built coil with cotton. After fixing, cut down the spare coils.
2. Drip a few drops of e-juice directly into the coil and cotton to make them fully saturated before use.
3. Put the airflow control ring on the tank, and then put the top cap on.
4. Put the completed upper part on the atomizer base and then the whole atomizer is assembled.

How to fill E-liquid?
Unplug the top cap and drip some e-liquid into the juice wells directly. After filling, fit on the top cap again.

How to adjust airflow?
By rotating the top airflow control ring clockwise or counterclockwise, you can adjust the airflow and get different vaping experiences.

Eleaf iJust 2 TC Atomizer User Manual

How to assemble
1.First mount the EC TC head onto the atomizer base;
2.Then put together atomizer base, atomizer tube and mouthpiece;
3.Finally assemble iJust 2 TC atomizer and temperature control battery together.

How to add liquid
1.First unscrew the atomizer base off the iJust 2 TC atomizer;
2.Then slowly refill the liquid into the hole along the atomizer tube;
3.Finally screw the atomizer base onto the iJust 2 TC atomizer again.
(Note: Please don’t add liquid into the air pipe and don’t overfill.)

How to adjust airflow
Put the silicone airflow control ring on the atomizer base. Then the amount of airflow can be adjusted by rotating the silicone airflow control ring so as to get different vaping experience.

Precautions 

1. Only have your iJust 2 TC atomizer repaired by Eleaf. Do not attempt to repair the unit by yourself as damage or personal injury may occur. 

2.Do not leave the iJust 2 TC atomizer in high temperatures or damp conditions,otherwise it may be damaged. The appropriate operation temperature is within -10℃ to 60℃ while using. 

3.Do not attempt to combine the iJust 2 TC atomizer with parts from other brands of e-cigarettes. If it is damaged in this way, our company will not take on responsibility and your warranty will be void.

Softwares for Eleaf iKonn 220

New firmware V1.06 made the following 3 upgrades for Eleaf iKonn 220:
1. Detecting resistance of coil in sleeping state;
2. Lowering the voltage value of “weak battery”;
3. Making preheat function visible.
Finally, download the file to upgrade your Eleaf iKonn 220 to V1.06.

NICOMORE M1 RDTA&RDA Luanching

This September, NICOMORE M1 comes to market with its innovative designs. The manufacture, NICOMORE, has long been at their best to create top pop atomizer catering to users' needs. At this launch, NICOMORE sacrifices no features. Instead, it squeezes in some new ones. Here is why NICOMORE becomes popular.

NICOMORE M1, comes with a height of 44.4 mm and a diameter of 24 mm. It weighs 55 g. This product is small but well built. The e-liquid volume is 1.5 ml. It is not a big one comparing with other vapes. The unique color of NICOMORE is classic black. Simple though it is, NICOMORE looks luxurious and delivers a high profile.

Users can fix coils by adjusting a particular system inside. What’s more, the electrodes deck is unique as well whose insulator is made of ceramic material. The ceramic material greatly protects atomizer from short circuit and also provides a high heat resistance. There is a liner inside the cover as well. It is made of peek that works well in terms of heat insulating.

Both RDTA and RDA are available on NICOMORE. Switching between the two modes is very convenient. This is one of the highlights of this product. Twisting the bottom to refill e-liquid does reduces the possibility of leaking oil. The position of air intake system adopts a concealed design, which makes the exterior more cool.

At present, NICOMORE has entered European market. Its initiative design with fixed fused coil is also getting popular on the other markets. NICOMORE is always trying to create product of rich feature. With an appealing outward appearance, the sophisticated technology, and the innovative design of structure, NICOMORE M1 will bring you special vapor and enjoyable flavor. Its features are quite enough for users’ needs, especially for those who want large clouds or enjoy DIY.

Wismec Presa User Manual

Presa is inspired by an ergonomically sculpted design to fit your hand. The anlarged fire button was designed so you can comfortably grip the device in many different ways. It is modern in appearance with an aesthetically pleasing design.

Other features include:
Enhanced manual safely lock switch
Temperature protection feature
OLED display
510 spring loaded connector
40W/ 10V with 2600mAh battery capacity

How to Use
Power on/ off: Clicking button 5 times continuously will turn device on/ off. To use, press and hold button down while in use. Let go of the button when done.

Adjust the Wattage/ Voltage: Press up / down adjustment button to increase/ decrease the wattage/ voltage.

Switch the VV/ VW Mode: Clicking fire button 3 times continuously to switch between VV/ VW mode. In VV mode, you can adjust output voltage between 2.0V-10.0V. In VW mode, you can adjust output wattage between 5W-40W.

Safety Lock Switch: Mode the lock switch right/ left to lock/ unlock the fire button so that unintentional press could be avoided.

Switch the Display Mode: By holding the up/ down adjustment buttons simultaneously for 2 seconds when the battery is off, the screen display will rotate 180 degrees. You can then view the screen from two kinds of angle through this operation.

How to Charge
The Presa is charged via tail USB port. It will take about 3-3.5hours to fully charge the battery with 1A charger. The battery power symbol on OLED screen will keep slowly flashing during charging and go out when the battery is fully charged.

Joyetech CUBOID Lite vs Eleaf iStick Kiya Kit

As the technology advances, many manufactures have promoted different devices with electronic display screens. Among various devices, we feel puzzled when we are selecting. Joyetech CUBOID Lite and Eleaf iStick Kiya are similar e-cigs but also have some differences so that I’d like to make a detailed comparison between them.

Similarities
Both CUBOID Lite and iStick Kiya feature a 1.45 inch screen. On this screen, we can find as much information as we need. The information includes the battery life, the output wattage and the most uniquely, we can know the real time. We can choose whichever parameter as we like and all of these are displayed in a clear and concise way. Additionally, these two devices are compact that can definitely ease your bag burden.

Differences
About the battery, CUBOID Lite is powered by 3000mAh cell and can fire up to 80w while the maximum output of iStick Kiya reach 50W powered by 1600mAh battery. Thus, iStick Kiya is lighter than CUBOID Lite and its weight is just 115.4g. Regarding the e-liquid capacity, they are slightly different. Originally, their e-liquid capacities are 2ml. However, CUBOID Lite has a spare glass tube. You just need to put the extended chimney on the atomizer and install the spare glass tube so that you can enlarge your e-liquid capacity to 3.5ml. This function can give more choices based on your own needs.

Conclusion
Each e-cig has advantages and defects. The principle of Eleaf iStick Kiya is “Less is More”, so for beginners, this device is a good choice. As for Joyetech CUBOID Lite, it has more functions to draw your attention.

Wismec Amor Mini Overview

How to replace the atomizer head?
Unscrew the atomizer base from the atomizer tube, and the atomizer head is located on the base. Just screw it and replace a new one.
Note: Please do not wash the atomizer head with water. Just clean it with cotton dry cloth.

How to fill e-liquid?
Unscrew the top cap from the vent pipe, inject the e-juice directly into the cambered slot. After filling, screw the top cap onto the atomizer tube again.
Note:
1. Please drip a few drops of e-juice into the atomizer head before the first use.
2. Make sure the e-liquid level is between 10%-90%.

How to adjust air inflow?
By rotating the airflow control ring clockwise or counterclockwise, you can adjust the airflow and get different vaping experience.

Is It Legal To Use E-cigar In Public?

In many countries, the legality of e-cigarette are still in controversy. Thus, in some countries, there are still barriers and regulations on the selling and usage of e-cigarettes. On the other hand, with the advancement in technology and dissemination of scientific knowledge about e-cigarette, it is gaining supports from the public.

E-cigarette has gained much popularity in the USA in the past. With its development, the government has made more regulations over its safety, which has contributed a lot to the quality control and safety insurance of e-cigarette production. In China, the manufacturing and selling of e-cigarette is legal. In addition, with the advantages in cost control and policy making, China is one of the biggest e-cigarette exporter. To buy e-cigarette, we have to firstly refer to the articles of law about the regulations of e-cigarettes in our own countries.

Though it is legal to buy and sell e-cigarette in some countries, it is not recommended to enjoy vape in public. As for e-cigarette itself, it is safe and doesn't contains any substances that will do harm to the health of surrounding people. However, it doesn't means that we can use them freely in public, because it will cause inconvenience and discomfort to others if they don't know much information about e-cigarettes. If there are conflicts caused by vape in the public, it is not for e-cigarette itself but for the discomfort that is brought to others.

From descriptions mentioned above, we can come to the conclusion that it is legal to use e-cigar in some countries, but it is not recommended to use in public. If we want to show our vaping skills in front of others, we can go to relevant clubs or online forum to find people with the same interests.

Wismec Amor Plus Quick Guide

Amor Plus Overview
The atomizer comes with a mouthpiece, a top cap, a seal ring 1(T type), a regulating component, a seal ring 2, a glass tube, an atomizer head and an atomizer base.

How to Fill E-liquid
Rotate the ring at the top of regulating component to expose the fill hole and then slowly fill the e-liquid into the glass tube. After filling the liquid, rotate the ring again to close the fill hole.
Note:
1. Please drip a few drops of e-juice into the atomizer head before the first use. 2. Air-inlet holes should be closed during filling. 3. Make sure the e-liquid level is between 10%-90%.

How to Vaping
Vaping Before vaping, please rotate the top regulating ring to the position as shown.
Note: The e-liquid inlet can be regulated by rotating the ring in a proper range, but make sure that the filling holes are closed when vaping.

How Can New Vapers Choose A Suitable Atomizer

Atomizer, as one of the most important parts of e-cigarette, is composed of two parts, heating wire and e-liquid storage tank. By simply pressing the power on/off button, atomizer started heating e-liquid powered by battery. To find a suitable atomizer for ourselves, we need to know more information about atomizer and choose the most suitable vapers for ourselves.

Classification
Atomizer is usually classified into cartomizer, clearomizer, tank atomizer, DIY rebuildable tank atomizer and DIY rebuildable dripper atomizer. The first three atomizer is finished products, which means that the coil is already made for us and we can directly add e-liquids and begin using it, which is simple and convenient to use. Generally speaking, we only need to replace the inner heating wire. DIY atomizer means that we have to make coil by ourselves, which is suitable for those who are good at hand-making and in pursuit of premium vaping experience.

The difference between tank atomizer and dripper atomizer lies in that tank atomizer is with a tank for storing e-liquid while dripper atomizer is without and we need to refill the e-liquid once it is used up. Dripper atomizer is less convenient than tank atomizer but it is usually with more vapor and powerful functions.

Importance
Atomizer is of great importance in the well functioning of e-cigarettes. Even with the same flavor e-liquids of the same quality, vaping experience can be totally different with different atomizers. Different atomizers are different in their structure, quantity of air input and parameter, and as a result the thickness of the vapor are totally different and thus provides a different vaping experience. For beginners, it is very important to find a suitable atomizer and experience the pure flavor of e-liquids.

Different atomizers are with their own features, each of which has its advantages and disadvantages. We have to firstly find out our real needs and make the decision with reference to the information provided above.

A Teardrop Suorin Drop Review

With so many traditional e-cigarettes in the market, we may feel tired of the same and single shape. The vape industry has noticed this problem and promoted some different e-cigarettes with unique design as well as the impressive performance. Suorin Drop Kit has drawn my attention because of its shape like a teardrop. I have some personal review on this produce based on my own vaping experience..

At first, I bought the Suorin Drop out of sheer curiosity as well as its distinctive appearance. Four colors are at our option. Its design is refined and solid compared with other products. It features rubberized finish which is very smooth and soft and we won’t feel cold when we are holding this especially in winter. As I mentioned above, its shape is like a teardrop that is very unique and elegant. Besides, its size is compact, much easy and convenient to carry it and put it in the pocket.

Having talked about its appearance, next I would like to discuss about its performance. This product is leak-resistant. It means that we don’t need to worry about the e-liquid leaking when we are vaping. Additionally, it features top-notch hit and it is a satisfyingly warm MTL draw which is very tight. The tank capacity is 2ml and its battery life is only 300mAh that may not satisfy some customers’ needs like large vapor production.

Each e-cigarette has its advantages and defects. But if you are a pod chaser and also the fan of MTL draw, you may be interested in Suorin Drop. What do you think about the Drop? Please write your comments below. If you are a new vaper, you can also choose the Eleaf iStick Trim  with GSTurbo Kit. The device was designed for you.

Eleaf iStick Kiya User Manual

How to Use?
Power on/off: press the fire button 5 times in quick succession to turn on or off the device.

Vaping: keep holding the fire button to take a puff when the device is powered on. Please choose the correct mode and adjust the wattage to a proper range according to your atomizer before use.

Charging: the Eleaf iStick Kiya can be charged through USB port via wall adapter or a computer.

Firmware upgrading: the firmware can be upgraded by connecting the device with a computer through the USB port via a micro USB cable.

General operations: 

Supplementary 
Instructions Parameters settings: under VW mode, the wattage can be adjusted simply by pressing + or - button; when TC(Ni, Ti, SS)/TCR(M1, M2, M3) mode is selected, the temperature can be adjusted simply by pressing + or - button while the wattage can only be adjusted under SET- TC POWER menu.
Note:
1. The TC-SS mode is especially designed for stainless steel 316 type coil only.
2. TC/TCR mode only supports a maximum of 1.5 ohm. The device will automatically switch to VW mode when the resistance is larger than 1.5 ohm.
3. When Kanthal wire is applied under TC/TCR mode, the device will also automatically switch to VW mode.

Stealth function: when stealth function is activated (STEALTH ON), you can vape with the display off and you can press the fire button once to see current setting.

Sub-parameters: sub-parameters include Puff (total vaping puffs), Time (total vaping seconds) and AMP (current amp). You can choose one of them to be displayed on the main interface.

Set clock: under SET-CLOCK menu, you’re free to set the time and date simply by pressing + button to move and pressing - button to adjust the digital.

Note:

1. When the device is powered on, you can select clock mode under MODE-CLOCK menu. And you’ll be able to check the time with a digital clock on the main interface.
2. When the device is powered off, you can check the time by one click of the fire button with a dial clock.

Preheat function: preheat function allows the device to quickly heat up the coil at a higher wattage within certain time limit. This function only works under VW mode When preheat function is activated, a letter “P” appears under the battery bar icon.

Timeout duration: once the duration is set (like 5 seconds), when you hold the fire button and vape over the pre-set time, it’ll display Over 5S protect and shut down automatically. Press the fire button 5 times to reactivate the device.

ENU ON: when the device is plugged in to charge, if temperature of the device is lower than -5℃ or higher than 45℃, the screen will respectively display “BATTERY TOO COLD” or “BATTERY TOO HOT”. In both situations, the device won’t charge. If the temperature reaches even higher than 50℃ during charging, the device won’t charge until temperature drops lower than 45℃ again.

About TCR mode: under TCR (Temperature Coefficient of Resistance) mode, the device can support different temperature control coils within different TCR value ranges and you can set the TCR at different values within proper range.

Following are different TCR value ranges for different coils for your reference:

Note: 1. The TCR value in the sheet is 10  multiplied of the actual TCR.         2. Our total range of TCR value is 1-1000. Indications and protections

Atomizer Short-circuit Protection: when atomizer short-circuit occurs, the screen will display “Atomizer Short”.

No Atomizer Alert: when you press the fire button and the screen displays “No Atomizer Found”. This is mainly because there’s no atomizer attached on the battery or it is not tightly secured.

Weak Battery Alert: in all vaping modes, when the device is working with an atomizer and the voltage of the batteries drops below 2.9V, the screen will display “Weak Battery”. Meanwhile, the output power will be reduced accordingly.

Low-voltage Protection: when the voltage of the device is below 3.3V, the screen will first display “Battery Low” and then “Lock”. Charge the device to reactivate it.

Atomizer Low Alert: when the resistance of coil is lower than 0.1ohm in VW/BYPASS mode or lower than 0.05ohm in TC/TCR modes, the screen will display “Atomizer Low”. 

Temperature Protection: in TC/TCR modes, when the actual temperature of coil reaches the set temperature, the screen will display "Temp Protection". You can continue to use the device normally. 

Device Too Hot Alert: if the temperature of device is over alert temperature, the output will shut off automatically and the screen will display “Device Too Hot”. You can continue to vape after it cools down. 

Warnings 

1. Please keep out of reach of children. 

2. This product is not recommended for use by young people, non-smokers, pregnant or breast-feeding women, or persons who are allergic/sensitive to nicotine.

Contra-indication
1. Do not attempt to repair the product by yourself as damage or personal injury may occur.
2. Do not leave the product in high temperature or damp conditions, otherwise it may be damaged.
3. Do not use this product for other purposes except only for vaping and don’t swallow the e-liquid.

Possible Adverse Effects
1. This product may be hazardous to health and contains nicotine which is addictive.
2. For people with adverse reaction after using this product, it is recommended to use the e-liquid with lower nicotine content or no nicotine.

CB-60 Satisfying the Niche Market

Background:
Nowadays, the vape market is undergone great changes. People used to focus their attention on nicotine-free e-liquid now switch to the nicotine salt-based e-juice. Wismec, as the industrial leading company, aims at catering to the needs of those customers. Quickly responding to the new trend of the vape market, Wismec launched its new product-Wismec CB-60 starter kit.

Basic information:
Wismec CB-60 Kit includes a CB-60 box and Amor NS atomizer. CB-60 kit applies a traditional design of Wismec products so that you can recognize it at once. It has a curved body, which makes the holding of it so comfortably. The clear and horizontal screen provides us with more clear data. The Wismec CB-60 Full Kit packs a 2300mAh internal battery and has a max output of 60W, yet it relatively compact and lightweight.

Spotlights:
The CB-60 kit with a Amor NS atomizer are geared for MTL vaping with the newly-introduced WS coil heads for optimal flavor. In addition, it is the first vape designed for high nicotine or nicotine salt-based e-liquid. The new spin on low-powered vaping is also a plus.

Recommendation:
This vape is suggested for smokers attempting to begin to vape. In this way, they can still have a great taste also may be with the help of this e-cigarette, those people can finally give up smoking.

What’s more, if you are a fan of MTL, Wismec CB-60 is also a wonderful option for you!

Eleaf Lyche Atomizer User Manual

How to use

1. First drip a few drops of e-liquid into the coil to make it fully saturated.

2. Then screw the atomizer head onto the top cap tightly, screw the atomizer base with glass tube onto the top cap tightly and finally put the mouthpiece on.

3. Rotate counterclockwise the regulation ring to open the e-liquid fill hole. Then slowly refill e-liquid into the atomizer. Close the e-liquid fill hole by rotating clockwise the regulation ring. (Note: please don’t overfill and take several puffs without activating the atomizer before use.)

4. The amount of airflow can be adjusted by rotating the airflow control ring on the top cap so as to get different vaping experiences, clockwise to increase and counterclockwise to decrease.

Precautions 

1. Only have your Eleaf LYCHE Atomizer repaired by Eleaf. Do not attempt to repair the unit by yourself as damage or personal injury may occur. 

2. Do not leave the LYCHE atomizer in high temperatures or damp conditions, otherwise it may be damaged. The appropriate operation temperature is from -10℃ to 60℃ while using. 

3. Do not attempt to combine the LYCHE atomizer with parts from other brands of e-cigarettes. If it is damaged in this way, our company will not take on responsibility and your warranty will be void. 

Warnings 

1. Please keep out of reach of children. 

2. This is not recommended for use by young people or non-smokers.

Wismec RX mini Kit User Manual

What functions dose RX mini Kit have?
1. Key lock function: While the device is on, simultaneously press the two regulatory buttons. This will switch between Key Lock and Key Unlock function.

2. Micro USB Port function: The USB port can be used for charging and upgrading firmware.

3. Resistance locked function: While the resistance sign blink, press the right regulatory button to lock or unlock the resistance of the atomizer. (Note: Such operation should be carried out at room temperature.)

How to use it?
1. Power on/off: Press the fire button 5 times in quick succession to turn the device on and off.
(Note: Please adjust the wattage to a proper range to match the atomizer you used before using.)
2. Stealth function: While the device is on, simultaneously hold the fire button and the left regulatory button. This will switch the screen display on and off.

3. Switch the display mode: By pressing the left and right regulatory buttons simultaneously in shutdown state, the screen display will rotate 180 degrees. You can then view the screen from two kinds of angle through this operation.

4. Shift among VW/Bypass/TC-Ni/TC-Ti/TC-SS/TCR Mode
Press the fire button 5 times to turn the Wismec RX mini Kit on. The OLED screen presents 4 rows of information:
(1). Mode (VW, Bypass, TC-Ni, TC-Ti, TC-SS, TCR) and Battery indicator
(2). Temperature in TC modes or Output wattage in VW/Bypass mode.
(3). Output wattage in TC modes or Voltage in VW/Bypass mode.
(4). User information (Current, Puff, Time) and Resistance

5. Vaping: When the device is powered on, long press the button to take a puff.

6. How to Reset: If you get stuck while upgrading, just press the right regulatory button and then insert into the reset hole with a needle to restart.

Eleaf Lemo 3 Atomizer User Manual

How to Use?
A. When used with pre-made or self-built coil as RTA:

1. Screw off the atomizer base, loosen the two screws on the RTA cap and take the RTA cap off. 

2. Fix the pre-made or self-built coil on the RTA base, activate the coil with your device till it goes red, and then put the cotton through the coil after the coil cools down. (Note: please make sure the finally fixed coil does not come into contact with the surface of the deck and the inner wall of the RTA cap.) 

3. Drip a few drops of e-liquid directly into the pre-made or self-built coil to make it fully saturated before use, put the RTA cap on and tighten the screws, and then screw the atomizer tube onto the atomizer base tightly. 

4. Screw off the top cap from the atomizer, slowly fill e-liquid into the atomizer along the glass tube and screw the top cap on tightly after filling. (Note: please don’t overfill and don’t fill e-liquid into the air pipe; please take several puffs without activating the atomizer and leave the atomizer sit for several minutes before use.)

5. The airflow can be adjusted by rotating the airflow control ring on the atomizer base. 

6. Finally the Eleaf Lemo 3 atomizer as RTA is ready for use. 

B.When used with atomizer head as ordinary atomizer:

1. Take off the RTA base from the atomizer base, and fix the atomizer head base on with screws tightened. 

2. Drip a few drops of e-liquid directly into the atomizer head to make it fully saturated before use, screw the atomizer head onto the atomizer head base tightly, and screw the atomizer tube on. 

3. Screw off the top cap from the atomizer, slowly fill e-liquid into the atomizer along the glass tube and screw the top cap on tightly after filling. (Note: please don’t overfill and don’t fill e-liquid into the air pipe; please take several puffs without activating the atomizer and leave the atomizer sit for several minutes before use.)

4. The airflow can be adjusted by rotating the airflow control ring on the atomizer base. 5. Finally the Lemo 3 atomizer is ready for use. 

Precautions 

1. Only have your Lemo 3 atomizer repaired by Eleaf. Do not attempt to repair the unit by yourself as damage or personal injury may occur. 

2. Do not leave the Lemo 3 atomizer in high temperatures or damp conditions, otherwise it may be damaged. The appropriate operation temperature is from -10℃ to 60℃ while using. 

3. Do not attempt to combine the Lemo 3 atomizer with parts from other brands of e-cigarettes. If it is damaged in this way, our company will not take on responsibility and your warranty will be void. 

Warnings 

1. Please keep out of reach of children. 

2. This is not recommended for use by young people or non-smokers. 

Wismec CB-60 is Going to Guide the Vape Market

Wismec has always been one of the leading manufacturers in the vape industry. It has a wide range of products including the tiny sized, those powerful vapes with triple batteries and 20700 cell. Wismec has never stop making innovation. As a great fan of Wismec, I am very excited to witness the launch of Wismec CB-60.

Detailed Features
Powered by an built-in 2300mAh battery, it can reach 60W, as also indicated from its name. Tiny and compact, it is easy to carry around. Featuring a temperature protection system, the vape kit can ensure you the safety of vaping. New WS03 coil can deliver you great mouth to lung experience. Other features like 2A current for quick charge, detachable structure for easy cleaning and repairing and top filling solution for easy adding of e-liquid.

Spotlight
The above features about Wismec CB-60 Full Kit is already breathtaking. However, hold your breathe for another wonderful advantage. It is unprecedented for you can not see this feature from any other vape. It is the first vape designed for high nicotine and Nic-salt use.

Reasons to buy
If you wanna say goodbye to traditional cigarettes, however you still miss the taste of it, the Wismec CB-60 is here to help you out of the trouble. You can have great vaping experience with Wismec CB-60 Kit.

Eleaf ELLO Atomizer Quick Start

Assembling:
1. Drip a few drops of e-liquid directly into the atomizer head to make the coil(s) inside fully saturated before first use;

2. Screw the primed atomizer head onto the atomizer base tightly;

3. Put the glass tube on, and screw the top cap with mouthpiece on;

4. Slide the mouthpiece back to reveal the fill port, slowly fill e-liquid into the tank through the port, and then close the retractable top after filling. (Note: please don’t overfill.)

5. The airflow can be adjusted by rotating the airflow control ring on the atomizer base;

6. Finally the Eleaf ELLO Atomizer is ready for use.

Warnings 

1. Please keep out of reach of children. 

2. This product is not recommended for use by young people, non-smokers, pregnant or breast-feeding women, or persons who are allergic/sensitive to nicotine.

Contra-indication

1. Do not attempt to repair the product by yourself as damage or personal injury may occur. 

2. Do not leave the product in high temperature or damp conditions, otherwise it may be damaged. 

3. Do not use this product for other purposes except only for vaping and don’t swallow the e-liquid. 

Possible Adverse Effects 

1. This product may be hazardous to health and contains nicotine which is addictive. 

2. For people with adverse reaction after using this product, it is recommended to use the e-liquid with lower nicotine content or no nicotine.

Wismec CB-60 Preview

      How many of the heavy smokers trying to use e-cigarettes to replace traditional tobacco products and find out that they can not resist the temptation of the flavor and nicotine. They can hardly give up smoking and switch to vape for most of the e-cigarettes designed for beginners are of low nicotine concentration. Most of them feel unsatisfied about the vaping experience.

      However, this time, in consideration of the demands of heavy smokers, Wismec designed a new vape-CB-60, perfect for high nicotine and nicotine salt e-liquid. The Wismec CB-60 vape kit packs a 2300mAh built-in battery, with a maximum output power of 60W, best for MTL experience. Besides, this vape kit really enjoys a compact and portable size, comparing to other products created by Wismec.

      The temperature protection system is introduced to protect the whole vaping process so that you can rest assured and enjoy vaping. Other features like top filling solution, bottom airflow control, and detachable structure are made for the convenient using of the vape. There are five colors for people to choose: silver, green, black, purple, bronze. All are classic colors.

      Wismec CB-60 vape kit is what you need right now! If you are a heavy smoke, then it is the right time to do the right thing-go and get a Wismec CB-60 kit. You will find the taste so similar to traditional tobacco products.

Eleaf iStick TC 200W User Manual

How to Use?
Power on/off: Unlock the battery cover on the bottom of the device and install three high-rate 18650 cells into iStick TC200W body correctly according to the marks of positive (+) and negative (-) poles on the battery cover. The device can be powered on/off by pressing the fire button 5 times.

Note:
1. Please be careful not to use cells with torn casings as it is a safety hazard.
2. Please make sure you are using three high-rate 18650 cells whose continuous discharge current should be above 25A.
3. Please be sure the voltage difference between every two 18650 cells is within 0.3V when the 18650 cells are installed.
4. Before using, please set the wattage within a proper range that the atomizer you installed can work with.

Vaping: Long press the fire button to take a puff. 

Stealth on/off: Press the fire button and left button simultaneously when the device is powered on to switch between Stealth On and Stealth Off mode. In Stealth On mode, you can vape with the OLED screen off and you can press the fire button one time to see current setting. 

Adjustment buttons lock/unlock: Keep pressing the left button and right button simultaneously for two seconds when the device is powered on, then the left and right buttons will be locked and the screen will display “Lock”. In the same way, the left and right buttons can be unlocked and the screen will display “Unlock”. Through this operation, you can protect the buttons from unintentional presses and prolong their lifespan. 

Switch display mode: Keep pressing left button and right button simultaneously for two seconds when the device is powered off, the screen display will rotate 180 degrees. You can view the screen from two different angles through this operation. 

Switch vaping modes: Long press the mode button to switch among VW, TC-Ni, TC-Ti, TC-SS, TCR-M1, TCR-M2, TCR-M3 modes.

1) In VW mode: When set in VW mode, the device can support a coil whose resistance is within the range of 0.1ohm-3.5ohm. 

Adjust wattage: In VW mode, the output wattage can be adjusted from 1W to 200W by pressing left button or right button, left button to decrease and right button to increase. Keep pressing left button or right button without looseness can rapidly decrease or increase the wattage level. 

2) In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2, M3) Mode: When set in TC-Ni/TC-Ti/TC-SS mode, the device can separately support Nickel 200, Titanium, and 316 Stainless Steel coils. In TCR (Temperature Coefficient of Resistance) mode, the device can support different temperature control coils within different TCR value ranges and you can set the TCR at different values within proper range. (Resistance range of coil: 0.05ohm-1.5ohm) 

The Setting of TCR Mode (M1,M2,M3): When the device is powered off, keep pressing the fire button and the right button simultaneously,then you will enter the TCR (M1,M2,M3) set menu: 

1. Press the left or right button to choose among M1, M2 and M3; 

2. Press the fire button one time to confirm the mode you chose; 

3. Press the left or right button to decrease or increase the TCR value according to the material of the coil you used; 

4. Keep pressing the fire button or stay in the interface for about 10 seconds to confirm your setting. 

Following are different TCR value ranges for different coils for your reference:

Note: 1. The TCR value in the sheet is 10  multiplied of the actual TCR.         2. Our total range of TCR value is 1-1000. 

Adjust wattage: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, the output wattage can be adjusted from 1W to 200W. Keep pressing the mode button and right button simultaneously without looseness to increase the wattage level. On the contrary, keep pressing the mode button and left button simultaneously without looseness to decrease the wattage level. 

Adjust temperature: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, temperature can be adjusted from 100-315℃ or 200-600℉ by pressing left button or right button, left button to decrease and right button to increase. Each press of the left or right button will decrease or increase the temperature setting by 5℃ or 10℉. Keep pressing left button or right button without looseness can rapidly decrease or increase temperature setting. 

Shift between ℃ and ℉: If you increase the temperature to 315 ℃, and continue to press the right button, the temperature reading will automatically change to the lowest Fahrenheit (200℉). Equally, if the temperature is set at the lowest Fahrenheit (200℉) and you continue to press the left button, the temperature reading will automatically change to the highest Celsius (315 ℃). 

Lock/Unlock resistance: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, keep pressing the fire button and right button simultaneously for two seconds to lock or unlock atomizer “base resistance”. The lock sign will appear when resistance is locked and “Ω” symbol will come back when unlocked.

Note: 

1. Please lock the resistance when the coil is at room temperature so that the device can display the correct “base resistance”. 

2. In resistance lock mode, when you remove the coil and then put it back, the device can maintain the same “base resistance” although the coil resistance may increase due to the rise of temperature. In resistance unlock mode, when you remove the coil and then put a coil back, the screen may display “New coil up same down” as the coil resistance may increase within certain range. If it is the same coil, press the left (-) button and if it is a new coil, press the right (+) button. But please unlock the resistance when you want to change an atomizer or a coil of different resistance. 

3. When using a common coil or a coil whose resistance is above 1.5ohm in TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode by mistake, the device will automatically switch to VW mode. 

Functions of Micro USB Port 

Charging: The battery power indicator on the screen of iStick TC200W will keep flashing when the remaining power of the 18650 cells is less than 10%. It is recommended to charge the 18650 cells with an external battery charger as it will take less time to give them a full charge. The cells can also be charged in the iStick TC200W through USB port via 1A wall adapter or a computer. If the 18650 cells are charged in the iStick TC200W, the battery indicator on the screen will keep flashing during charging and the screen will go out when fully charged. 

Firmware Upgrading: The firmware can be upgraded by connecting the device with a computer through the USB port via a micro USB cable. 

Protections and Alerts 

Atomizer Protection: Each time when vaping time exceeds 10 seconds, the output shuts off automatically with “Over 10s” display on the screen. 

Atomizer Low Alert: When the resistance of coil is lower than 0.1ohm in VW mode or lower than 0.05ohm in TC modes, the screen will display “Atomizer Low”. 

Atomizer Short-circuit & No Atomizer Protection: When atomizer short-circuit occurs, the OLED screen will display “Atomizer Short”. The screen will display “No Atomizer” when there is no atomizer connected. 

Low-voltage Protection: When the voltage of the cell is below 3.1V, the screen will first display “Battery Low” and then “Lock”. Charge the cells to reactivate the device. 

Temperature Protection: In TC modes, when the actual temperature of coil reaches the set temperature, the screen will display "Temp Protection". You can continue to use the device normally. 

Temperature Alert: If the temperature of device is over alert temperature, the output will shut off automatically and the screen will display “Device Too Hot”. You can continue to vape after it cools down. 

Weak Battery Alert: In all vaping modes, when the device is working with an atomizer and the voltage of the cell drops below 2.9V, the screen will display “Weak Battery”. Meanwhile, the output power will be reduced accordingly. 

Imbalanced Alert: If the voltage difference between two cells is equal to or more than 0.3V, the device will display “Imbalanced” when plugged in. Please fully charge the cells externally or replace the cells with freshly charged cells. 

Check Battery Alert: If the cells are installed incorrectly, the screen will display “Check Battery”. 

Charge Error Alert: When no current is detected in charging state, the screen will display “Charge Error”. 

Check USB Alert: If the voltage of the USB charger is equal to or more than 5.8V, the device will display “check USB” when plugged in or vaping. 

Precautions 

1. Only have your iStick TC200W repaired by Eleaf. Do not attempt to repair the unit by yourself as damage or personal injury may occur. 

2. Do not leave the iStick TC200W in high temperatures or damp conditions, otherwise it may be damaged. The appropriate operation temperature is within 0℃ to45℃ while charging and -10℃ to 60℃ while using. 

3. Do not attempt to combine the Eleaf iStick TC200W mod with parts from other brands of e-cigarettes. If it is damaged in this way, our company will not take on responsibility and your warranty will be void. 

Warnings 

1. Please keep out of reach of children. 

2. This device is not recommended for use by young people or non-smokers. 

How To Operate ASTER Total Correctly?

Product Introduction 

ASTER Total is a skillfully engineered e-cigarette kit with inbuilt tank in a compact package. With direct output voltage system, to power it on or off or to activate it can all be done by holding the button. The e-liquid can easily be refilled by removing the top cap only and the airflow can be adjusted to your preference. Also with an ergonomically redesigned shape, you can hold it in the palm with ease and comfort.

How to Operate

Assembling: 
1. Drip a few drops of e-liquid into the coil to make it fully saturated before first use, and then screw the atomizer head onto the air pipe tightly.
2. Screw the air pipe together with atomizer head into the tank.
3. Slowly fill e-liquid through the slot on the air pipe into the tank, and screw the top cap with mouthpiece on after filling. (Note: please don’t overfill and don’t fill e-liquid into the air pipe; please take several puffs without activating the device and leave the device sit for several minutes before use.)
4. The airflow can be adjusted by rotating the airflow control ring.
5. Finally the ASTER Total is ready to use.

Power on/off:
Press the button 5 times in quick succession within two seconds, the white button light will flash 5 times to show ASTER Total is powered on. In the same way, it can also be turned off.

Vaping: Long press the button to take a puff.

Charging: Charge device by connecting it with wall adapter or computer via USB cable. The light turns red when the Eleaf ASTER Total Starter Kit is charging and the light will go out when fully charged. It will take about 2.5 hours to get a full charge via 1A wall adapter.

Properties and Protections 

Atomizer Protection: When vaping time exceeds 15 seconds, the device shuts off automatically with the white button light flashing 10 times.

Short-circuit Protection: When the resistance is less than 0.15ohm, short-circuit occurs with the white button light flashing 3 times.

No Atomizer Protection: The white button light will flash slowly when the button is pressed down without atomizer connected.

Low-voltage Protection: When the voltage of the device is below 3.3V, the white button light will flash 40 times. At the same time, the device won’t turn on. Charge the device to reactivate it.

Battery Level Indication Function: The white button light will stay lit or flash slowly after a puff when the battery level is high. On the contrary, the light will flash in frequency.

Eleaf iStick Pico 25 User Manual

Product Introduction
The Eleaf iStick Pico 25 ingeniously packs a big 0.91-inch screen that offers a concise and clear interface, 2A quick charge capability and upgradeable firmware with preheat function in a compact, stylish yet powerful package. Powered by single 18650 battery, the iStick Pico 25 is capable of outputting a maximum power of 85W and can handle various tanks up to 25mm diameter. The ELLO atomizer that features the HW coil for ultimate flavor and retractable top for easy filling pairs with the iStick Pico 25 perfectly in terms of both appearance and performance.

How to Use?
Power on/off: screw off the battery cap, put one high-rate 18650 battery (positive side down and negative side up) into iStick Pico 25 and finally screw the battery cap on. The device can be powered on/off by pressing the fire button 5 times

Note:
1.Please be careful not to use battery with torn casing as it is a safety hazard. 2.Please make sure you are using high-rate 18650 battery whose continuous discharge current is above 25A.
3.Before using, please set the wattage within a proper range that the atomizer you installed can work with.

Vaping: when the device is powered on, long press the fire button to take a puff.

Stealth on/off: press the fire button and “-” button simultaneously when the device is powered on to switch between Stealth On and Stealth Off mode. In Stealth On mode, you can vape with the OLED screen off and you can press the fire button once to see current setting.

Adjustment buttons lock/unlock: keep pressing “+” button and “-” button simultaneously for two seconds when the device is powered on, then the adjustment buttons will be locked and the screen will display “Key Lock”. In the same way, the adjustment buttons can be unlocked and the screen will display “Key Unlock”. Through this operation, you can protect the buttons from unintentional presses and prolong their lifespan.

Switch display mode: keep pressing “+” button and “-” button simultaneously for two seconds when the device is powered off, the screen display will rotate 180 degrees. You can view the screen from two different angles through this operation.

Switch display interfaces: in power-on state, choose VW mode; keep holding “+” button and fire button till the current interface flashes; when it’s flashing, press “+”or “-” button to switch among different interfaces; finally press fire button once to confirm the interface you chose.

Note: the interface can only be changed and selected under VW mode in power-on state. And when one interface is selected under VW mode, the interfaces of Bypass /TC (Ni, Ti, SS, M1, M2, M3) modes will change accordingly and automatically.

Preheat function: in power-off state, keep holding “+” button and fire button till the M1 mode appears; press the fire button 3 times to “Power”, and press “+” or “-” button to adjust the wattage of preheat; press the fire button again to “Time”, and press “+” or “-” button to adjust the second of preheat or to turn off the preheat function.

Switch vaping modes: when the device is powered on, press the fire button 3 times in quick succession, the device will display current vaping mode. Press the “+” or “-” button to switch among VW,  Bypass,TC-Ni, TC-Ti, TC-SS, TCR-M1, TCR-M2, TCR-M3 modes and then press the fire button once or stay in the interface for about 10 seconds to confirm the vaping mode you chose.

1) VW mode: When set in VW mode, the device can support a coil whose resistance is within the range of 0.1ohm-3.5ohm. Adjust wattage: in this mode, the output wattage can be adjusted from 1W to 85W by pressing “+” button or “-” button, “+” button to increase and “-” button to decrease. Long press “+” or “-” button can rapidly increase or decrease the wattage level.

2) Bypass mode: When set in Bypass mode, the device can support a coil whose resistance is within the range of 0.1ohm-3.5ohm. Direct output voltage system is applied in this mode. The higher the battery level, the higher the output voltage.

3) TC-Ni/TC-Ti/TC-SS/TCR(M1, M2, M3) Mode: When set in TC-Ni/TC-Ti/TC-SS mode, the device can separately support Nickel 200, Titanium, and Stainless Steel 316 coils. In TCR (Temperature Coefficient of Resistance) mode, the device can support different temperature control coils within different TCR value ranges and you can set the TCR at different values within proper range. (Resistance range of coil: 0.05ohm-1.5ohm)

The Setting of TCR Mode (M1,M2,M3): when the device is powered off, keep pressing the fire button and the “+” button simultaneously, then you will enter into the TCR (M1,M2,M3) set menu:
1. Press the fire button repeatedly to choose among M1, M2 and M3 modes;
2. Press the “+” or “-” button to increase or decrease the TCR value according to the material of the coil you use;
3. Keep pressing the fire button or stay in the interface for about 10 seconds to confirm your setting.

Following are different TCR value ranges for different coils for your reference:

Note: 1.The TCR value in the sheet is 10  multiplied of the actual TCR.
    2.Our total range of TCR value is 1-1000.

Adjust wattage: in TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, the output wattage can be adjusted from 1W to 85W. Press the fire button 4 times in quick succession to enter the wattage setting menu and press “+” or “-” button to increase or decrease the wattage level. Keep pressing “+” or “-” button without looseness to rapidly increase or decrease the wattage level.

Adjust temperature: in TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, temperature can be adjusted from 100-315℃ or 220-600℉ by pressing “+” or “-” button, “+” button to increase and “-” button to decrease. Each press of the “+” or “-” button will increase or decrease the temperature setting by 5℃ or 10℉. Keep pressing “+” or “-” button without looseness can rapidly increase or decrease temperature setting.

Shift between ℃ and ℉: if you increase the temperature to 315 ℃, and continue to press the “+” button, the temperature reading will automatically change to the lowest Fahrenheit (220℉). Equally, if the temperature is set at the lowest Fahrenheit (220℉) and you continue to press the “-” button, the temperature reading will automatically change to the highest Celsius (315 ℃).

Lock/Unlock resistance: in TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, when the device is powered on, keep pressing the fire button and “+” button simultaneously for two seconds to lock or unlock atomizer “base resistance”. The lock sign will appear when resistance is locked and “Ω” symbol will come back when unlocked.

Note:
1.Please lock the resistance when the coil is at room temperature so that the device can display the correct “base resistance”.

2.In resistance lock mode, when you remove the coil and then put it back, the device can maintain the same “base resistance” although the coil resistance may increase due to the rise of temperature. In resistance unlock mode, when you remove the coil and then put a coil back, the screen may display “New coil up same down” as the coil resistance may increase within certain range. If it is the same coil, press the “-” button and if it is a new coil, press the “+” button. But please unlock the resistance when you want to change an atomizer or a coil of different resistance.

3.When using a common coil or a coil whose resistance is above 1.5ohm in TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode by mistake, the device will automatically switch back to VW mode.

How to put custom logo in the device?
Download the file on our official website, plug the device in with USB cable to a computer, and double click the EleafUpdate.exe. Then click “LOGO” and open the image you choose to put it in the device. Finally press the fire button twice in quick succession when the device is powered on to enter logo on/off interface and press “+” button or “-” button once to turn on/off logo.
Note:
1. Please make sure the image you choose is a monochrome image of 96*32 pixels in the format of bmp.
2. If you fail to put the custom logo in and the device shuts down, press the “-” button once to restart the device.

Functions of Micro USB Port
Charging: The battery power indicator on the screen of the device will keep flashing when the remaining power of the 18650 battery is less than 10%. The 18650 battery can be charged in the device through USB port via wall adapter or a computer or charged with an external battery charger. If the 18650 battery is charged in the device, the battery bar on the screen will keep flashing during charging and the screen will go out when fully charged.

Firmware Upgrading: The firmware can be upgraded by connecting the device with a computer through the USB port via a micro USB cable.

Properties
Atomizer Protection: each time when vaping time exceeds 10 seconds, the output shuts off automatically with “Over 10s” display on the screen. Atomizer Low Alert: when the resistance of coil is lower than 0.1ohm in VW/Bypass mode or lower than 0.05ohm in TC modes, the screen will display “Atomizer Low”.

Atomizer Short-circuit & No Atomizer Protection: when atomizer short-circuit occurs, the screen will display “Atomizer Short”. The screen will display “No Atomizer” when there is no atomizer connected.

Low-voltage Protection: when the voltage of the battery is below 3.3V, the screen will first display “Battery Low” and then “Lock”. Charge the battery to unlock the device.

Temperature Protection: in TC modes, when the actual temperature of coil reaches the set temperature, the screen will display "Temp Protection". You can continue to use the device normally.

Temperature Alert: if the temperature of device is over alert temperature, the output will shut off automatically and the screen will display “Device Too Hot”. You can continue to vape after it cools down.

Weak Battery Alert: in all vaping modes, when the device is working with an atomizer and the voltage of the battery drops below 2.9V, the screen will display “Weak Battery”. Meanwhile, the output power will be reduced accordingly. Warranty We are not responsible for any damages caused by human error. Legal warranty is applied.

Warnings
1. Please keep out of reach of children.
2. This product is not recommended for use by young people, non-smokers, pregnant or breast-feeding women, or persons who are allergic/sensitive to nicotine.

Contra-indication
1. Do not attempt to repair the product by yourself as damage or personal injury may occur.
2. Do not leave the product in high temperature or damp conditions, otherwise it may be damaged.
3. Do not use this product for other purposes except only for vaping and don’t swallow the e-liquid.

Possible Adverse Effects
1. This product may be hazardous to health and contains nicotine which is addictive.
2. For people with adverse reaction after using this product, it is recommended to use the e-liquid with lower nicotine content or no nicotine.