Eleaf iCare Solo User Manual
Notice for Use
Thank you for choosing Eleaf products! Please read this manual carefully before use so as to use correctly. If you require additional information or have questions about the product or its use, please consult your local agents, or visit our website at www.istick.org.
Product Introduction
Tiny yet cute looking, the Eleaf iCare Solo Starter Kit is an integration of an inbuilt battery and a tank in one unit, which is quite simple to use and convenient to carry. With LEDs in three different colors, you can easily check the battery level by a simple glance at the light. Various colors and great vaping flavor also make the iCare Solo an optimal choice for starter vapers.
How to use?
Assembling:
1. Remove the mouthpiece, and then unscrew the air pipe and take it out.
2. Slowly fill e-liquid into the tank. (Note:please don’t fill beyond the Max line to avoid overflow.)
3. Drip 2 or 3 drops of e-liquid directly into the coil before first use, and screw the atomizer head on the air pipe tightly.
4. Insert the air pipe with atomizer head into the tank again and tighten it.
5. Finally put back the mouthpiece, and the iCare Solo is ready to use.
Power on/off: Press the button 5 times in quick succession within two seconds, the indicator light will flash 3 times to show the device is ready for use. In the same way, it can also be turned off.
Vaping: Keep holding the button to take a puff when the device is powered on. When vaping, the indicator light stays lit. When the battery level is between 100%-16%, the indicator light is green; when the battery level is between 15%-6%, the indicator light is yellow; when the battery level is no higher than 5%, the indicator light is red.
Charging: The device can be charged by connecting it with 1A wall adapter or computer via the USB cable. It will take about 1 hour to get a full charge via 1A wall adapter. The charging indicator light is red during charging and goes out when fully charged.
Properties and Protections:
Atomizer Protection: Every time when vaping time exceeds 10 seconds, the indicator light flashes 10 times and the output cuts off automatically.
Short Circuit Protection: If short circuit occurs before vaping, the indicator light will flash 5 times and the output cuts off automatically when you start to vape; if short circuit occurs during vaping, the indicator light will flash 3 times.
Low Voltage Protection: When the voltage of the device is lower than 3.3V, the red indicator light flashes 20 times and there is no output when vaping. Charge the device to reactivate it.
Resistance Detect: If the output load resistance is higher than 3.5ohm, the indicator light will flash slowly to indicate that no atomizer is detected when vaping; if the output load resistance is lower than 1.0ohm, the indicator light will flash 5 times to indicate a low output load or a short circuit when vaping.
Output Voltage: When the voltage of the device is no lower than 3.7V, the output voltage is constant 3.7V; when the voltage of the device is lower than 3.7V, the output voltage changes according to the battery level.
Warranty
We are not responsible for any damages caused by human error. Legal warranty is applied.
Warnings
1. Please keep out of reach of children.
2. This product is not recommended for use by young people, non-smokers, pregnant or breast-feeding women, or persons who are allergic/sensitive to nicotine.
Contra-indication
1. Do not attempt to repair the product by yourself as damage or personal injury may occur.
2. Do not leave the product in high temperature or damp conditions, otherwise it may be damaged.
3. Do not use this product for other purposes except only for vaping and don’t swallow the e-liquid.
Possible Adverse Effects
1. This product may be hazardous to health and contains nicotine which is addictive.
2. For people with adverse reaction after using this product, it is recommended to use the e-liquid with lower nicotine content or no nicotine.
Thank you for choosing Eleaf products! Please read this manual carefully before use so as to use correctly. If you require additional information or have questions about the product or its use, please consult your local agents, or visit our website at www.istick.org.
Product Introduction
Tiny yet cute looking, the Eleaf iCare Solo Starter Kit is an integration of an inbuilt battery and a tank in one unit, which is quite simple to use and convenient to carry. With LEDs in three different colors, you can easily check the battery level by a simple glance at the light. Various colors and great vaping flavor also make the iCare Solo an optimal choice for starter vapers.
How to use?
Assembling:
1. Remove the mouthpiece, and then unscrew the air pipe and take it out.
2. Slowly fill e-liquid into the tank. (Note:please don’t fill beyond the Max line to avoid overflow.)
3. Drip 2 or 3 drops of e-liquid directly into the coil before first use, and screw the atomizer head on the air pipe tightly.
4. Insert the air pipe with atomizer head into the tank again and tighten it.
5. Finally put back the mouthpiece, and the iCare Solo is ready to use.
Power on/off: Press the button 5 times in quick succession within two seconds, the indicator light will flash 3 times to show the device is ready for use. In the same way, it can also be turned off.
Vaping: Keep holding the button to take a puff when the device is powered on. When vaping, the indicator light stays lit. When the battery level is between 100%-16%, the indicator light is green; when the battery level is between 15%-6%, the indicator light is yellow; when the battery level is no higher than 5%, the indicator light is red.
Charging: The device can be charged by connecting it with 1A wall adapter or computer via the USB cable. It will take about 1 hour to get a full charge via 1A wall adapter. The charging indicator light is red during charging and goes out when fully charged.
Properties and Protections:
Atomizer Protection: Every time when vaping time exceeds 10 seconds, the indicator light flashes 10 times and the output cuts off automatically.
Short Circuit Protection: If short circuit occurs before vaping, the indicator light will flash 5 times and the output cuts off automatically when you start to vape; if short circuit occurs during vaping, the indicator light will flash 3 times.
Low Voltage Protection: When the voltage of the device is lower than 3.3V, the red indicator light flashes 20 times and there is no output when vaping. Charge the device to reactivate it.
Resistance Detect: If the output load resistance is higher than 3.5ohm, the indicator light will flash slowly to indicate that no atomizer is detected when vaping; if the output load resistance is lower than 1.0ohm, the indicator light will flash 5 times to indicate a low output load or a short circuit when vaping.
Output Voltage: When the voltage of the device is no lower than 3.7V, the output voltage is constant 3.7V; when the voltage of the device is lower than 3.7V, the output voltage changes according to the battery level.
Warranty
We are not responsible for any damages caused by human error. Legal warranty is applied.
Warnings
1. Please keep out of reach of children.
2. This product is not recommended for use by young people, non-smokers, pregnant or breast-feeding women, or persons who are allergic/sensitive to nicotine.
Contra-indication
1. Do not attempt to repair the product by yourself as damage or personal injury may occur.
2. Do not leave the product in high temperature or damp conditions, otherwise it may be damaged.
3. Do not use this product for other purposes except only for vaping and don’t swallow the e-liquid.
Possible Adverse Effects
1. This product may be hazardous to health and contains nicotine which is addictive.
2. For people with adverse reaction after using this product, it is recommended to use the e-liquid with lower nicotine content or no nicotine.
.jpg)
%20MTL%20RTA%E6%A8%AA%E5%B9%85.jpg)
No comments