Eleaf iStick TC 200W User Manual
Power on/off: Unlock the battery cover on the bottom of the device and install three high-rate 18650 cells into iStick TC200W body correctly according to the marks of positive (+) and negative (-) poles on the battery cover. The device can be powered on/off by pressing the fire button 5 times.
Note:
1. Please be careful not to use cells with torn casings as it is a safety hazard.
2. Please make sure you are using three high-rate 18650 cells whose continuous discharge current should be above 25A.
3. Please be sure the voltage difference between every two 18650 cells is within 0.3V when the 18650 cells are installed.
4. Before using, please set the wattage within a proper range that the atomizer you installed can work with.
Vaping: Long press the fire button to take a puff.
Stealth on/off: Press the fire button and left button simultaneously when the device is powered on to switch between Stealth On and Stealth Off mode. In Stealth On mode, you can vape with the OLED screen off and you can press the fire button one time to see current setting.
Adjustment buttons lock/unlock: Keep pressing the left button and right button simultaneously for two seconds when the device is powered on, then the left and right buttons will be locked and the screen will display “Lock”. In the same way, the left and right buttons can be unlocked and the screen will display “Unlock”. Through this operation, you can protect the buttons from unintentional presses and prolong their lifespan.
Switch display mode: Keep pressing left button and right button simultaneously for two seconds when the device is powered off, the screen display will rotate 180 degrees. You can view the screen from two different angles through this operation.
Switch vaping modes: Long press the mode button to switch among VW, TC-Ni, TC-Ti, TC-SS, TCR-M1, TCR-M2, TCR-M3 modes.
1) In VW mode: When set in VW mode, the device can support a coil whose resistance is within the range of 0.1ohm-3.5ohm.
Adjust wattage: In VW mode, the output wattage can be adjusted from 1W to 200W by pressing left button or right button, left button to decrease and right button to increase. Keep pressing left button or right button without looseness can rapidly decrease or increase the wattage level.
2) In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2, M3) Mode: When set in TC-Ni/TC-Ti/TC-SS mode, the device can separately support Nickel 200, Titanium, and 316 Stainless Steel coils. In TCR (Temperature Coefficient of Resistance) mode, the device can support different temperature control coils within different TCR value ranges and you can set the TCR at different values within proper range. (Resistance range of coil: 0.05ohm-1.5ohm)
The Setting of TCR Mode (M1,M2,M3): When the device is powered off, keep pressing the fire button and the right button simultaneously,then you will enter the TCR (M1,M2,M3) set menu:
1. Press the left or right button to choose among M1, M2 and M3;
2. Press the fire button one time to confirm the mode you chose;
3. Press the left or right button to decrease or increase the TCR value according to the material of the coil you used;
4. Keep pressing the fire button or stay in the interface for about 10 seconds to confirm your setting.
Following are different TCR value ranges for different coils for your reference:
Note: 1. The TCR value in the sheet is 10 multiplied of the actual TCR. 2. Our total range of TCR value is 1-1000.
Adjust wattage: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, the output wattage can be adjusted from 1W to 200W. Keep pressing the mode button and right button simultaneously without looseness to increase the wattage level. On the contrary, keep pressing the mode button and left button simultaneously without looseness to decrease the wattage level.
Adjust temperature: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, temperature can be adjusted from 100-315℃ or 200-600℉ by pressing left button or right button, left button to decrease and right button to increase. Each press of the left or right button will decrease or increase the temperature setting by 5℃ or 10℉. Keep pressing left button or right button without looseness can rapidly decrease or increase temperature setting.
Shift between ℃ and ℉: If you increase the temperature to 315 ℃, and continue to press the right button, the temperature reading will automatically change to the lowest Fahrenheit (200℉). Equally, if the temperature is set at the lowest Fahrenheit (200℉) and you continue to press the left button, the temperature reading will automatically change to the highest Celsius (315 ℃).
Lock/Unlock resistance: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, keep pressing the fire button and right button simultaneously for two seconds to lock or unlock atomizer “base resistance”. The lock sign will appear when resistance is locked and “Ω” symbol will come back when unlocked.
Note:
1. Please lock the resistance when the coil is at room temperature so that the device can display the correct “base resistance”.
2. In resistance lock mode, when you remove the coil and then put it back, the device can maintain the same “base resistance” although the coil resistance may increase due to the rise of temperature. In resistance unlock mode, when you remove the coil and then put a coil back, the screen may display “New coil up same down” as the coil resistance may increase within certain range. If it is the same coil, press the left (-) button and if it is a new coil, press the right (+) button. But please unlock the resistance when you want to change an atomizer or a coil of different resistance.
3. When using a common coil or a coil whose resistance is above 1.5ohm in TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode by mistake, the device will automatically switch to VW mode.
Functions of Micro USB Port
Charging: The battery power indicator on the screen of iStick TC200W will keep flashing when the remaining power of the 18650 cells is less than 10%. It is recommended to charge the 18650 cells with an external battery charger as it will take less time to give them a full charge. The cells can also be charged in the iStick TC200W through USB port via 1A wall adapter or a computer. If the 18650 cells are charged in the iStick TC200W, the battery indicator on the screen will keep flashing during charging and the screen will go out when fully charged.
Firmware Upgrading: The firmware can be upgraded by connecting the device with a computer through the USB port via a micro USB cable.
Protections and Alerts
Atomizer Protection: Each time when vaping time exceeds 10 seconds, the output shuts off automatically with “Over 10s” display on the screen.
Atomizer Low Alert: When the resistance of coil is lower than 0.1ohm in VW mode or lower than 0.05ohm in TC modes, the screen will display “Atomizer Low”.
Atomizer Short-circuit & No Atomizer Protection: When atomizer short-circuit occurs, the OLED screen will display “Atomizer Short”. The screen will display “No Atomizer” when there is no atomizer connected.
Low-voltage Protection: When the voltage of the cell is below 3.1V, the screen will first display “Battery Low” and then “Lock”. Charge the cells to reactivate the device.
Temperature Protection: In TC modes, when the actual temperature of coil reaches the set temperature, the screen will display "Temp Protection". You can continue to use the device normally.
Temperature Alert: If the temperature of device is over alert temperature, the output will shut off automatically and the screen will display “Device Too Hot”. You can continue to vape after it cools down.
Weak Battery Alert: In all vaping modes, when the device is working with an atomizer and the voltage of the cell drops below 2.9V, the screen will display “Weak Battery”. Meanwhile, the output power will be reduced accordingly.
Imbalanced Alert: If the voltage difference between two cells is equal to or more than 0.3V, the device will display “Imbalanced” when plugged in. Please fully charge the cells externally or replace the cells with freshly charged cells.
Check Battery Alert: If the cells are installed incorrectly, the screen will display “Check Battery”.
Charge Error Alert: When no current is detected in charging state, the screen will display “Charge Error”.
Check USB Alert: If the voltage of the USB charger is equal to or more than 5.8V, the device will display “check USB” when plugged in or vaping.
Precautions
1. Only have your iStick TC200W repaired by Eleaf. Do not attempt to repair the unit by yourself as damage or personal injury may occur.
2. Do not leave the iStick TC200W in high temperatures or damp conditions, otherwise it may be damaged. The appropriate operation temperature is within 0℃ to45℃ while charging and -10℃ to 60℃ while using.
3. Do not attempt to combine the Eleaf iStick TC200W mod with parts from other brands of e-cigarettes. If it is damaged in this way, our company will not take on responsibility and your warranty will be void.
Warnings
1. Please keep out of reach of children.
2. This device is not recommended for use by young people or non-smokers.
.jpg)
%20MTL%20RTA%E6%A8%AA%E5%B9%85.jpg)
No comments